Brand: SANYO
Category: Camcorder
Document Type: Manual
Language: EN
Manual for VPC-PD2
Uploaded: Aug. 10, 2025, 12:14 a.m.
Warranty Information
Sanyo Electric shall not be held responsible for any problems resulting from the use of this camera or damages due to improper use.
Installing the battery pack and card: Insert the card and battery pack into the camera. The card is not included and must be purchased separately. The camera has internal memory.
Charging the battery pack: Turn off the camera. Connect the camera to a computer using the supplied USB cable. Turn on the computer. Charging begins when the multi-indicator turns red and stops when it turns off. Charging takes approximately 180 minutes.
Shooting: Turn on the camera. To record a video, press the video recording button. To stop recording, press it again. To take a photo, press the photo shooting button.
Playback: Press the REC/PLAY button. Use the arrow keys to select the desired image and press the SET button to play it.
Deleting files: In playback mode, select the file to delete, press the [/] button, select "DELETE SINGLE", and press the SET button.
Copying data to computer: Connect the camera to a computer via USB. Turn on both devices. Select "CARD READER" on the camera. Open the drive and copy files.
Dismounting the camera: Safely remove hardware from the task tray, then select the camera drive before disconnecting.
Charging the battery pack: Turn off the camera. Connect the camera to a computer using the supplied USB cable. Turn on the computer. Charging begins when the multi-indicator turns red and stops when it turns off. Charging takes approximately 180 minutes.
Shooting: Turn on the camera. To record a video, press the video recording button. To stop recording, press it again. To take a photo, press the photo shooting button.
Playback: Press the REC/PLAY button. Use the arrow keys to select the desired image and press the SET button to play it.
Deleting files: In playback mode, select the file to delete, press the [/] button, select "DELETE SINGLE", and press the SET button.
Copying data to computer: Connect the camera to a computer via USB. Turn on both devices. Select "CARD READER" on the camera. Open the drive and copy files.
Dismounting the camera: Safely remove hardware from the task tray, then select the camera drive before disconnecting.
Troubleshooting and error codes
| Category | Question | Answer | Action |
| Viewing images | Why is there a motor-like sound during video clip playback? | The sound of the camera's mechanical action was recorded. | Not a malfunction. |
| Connecting to a TV | Why is there no sound? | The volume on the TV is set to the minimum. | Adjust the volume on the TV. |
| Misc. | Why does the "Insufficient card memory" or "Insufficient internal memory” message appear? | There is no more available memory on the card or in the camera's internal memory. | Delete unnecessary files, or use a card that has more memory available. |
| Misc. | Why does the "Card is protected" message appear? | The lock switch on the card is in the locked (protect) position. | Move the lock switch to the unlocked position. |
| Misc. | Why can't the camera be operated? | A temporary internal circuitry problem may be the cause. | Remove the battery pack from the camera, wait a few minutes, then reinstall the battery pack and try again. |
| Misc. | A problem such as inability to record or play back occurs. | The card contains files that were saved using a device other than this camera. | After saving your files to a different medium, format the card. |
| Misc. | Can I use my camera abroad? | When the camera is connected to a TV, you can switch the camera's video output to NTSC or PAL. If you have questions about accessories etc., please consult with a dealer near you for advice. | |
| Misc. | Why does the "System error” message appear? | A problem has occurred within the camera or card. | Check the following items: ① Remove the card and then install it again. ② Remove the battery pack and then install it again. ③ Install a different card. If "System error" still appears after performing the above steps, then take the camera to the dealer for service. |