Name: Manual for HW80-B14959U1
Brand: Haier
Availability: InStock

Troubleshooting and error codes

Problem	Cause	Solution
CLr FLER	Drainage error, water is not fully drained within 6 minutes.	• Clean pump filter. • Check drain hose installation.
E2	Lock error.	• Shut the door properly.
E4	Water level not reached after 12 minutes.	• Make sure that tap is fully opened and water pressure is normal.
E8	Water protective level error.	• Drain hose is self-syphoning. • Check drain hose installation. • Contact the After sales service.
F3	Temperature sensor error.	• Contact the After sales service.
F4	Heating error.	• Contact the After sales service.
F7	Motor error.	• Contact the After sales service.
FR	Water level sensor error.	• Contact the After sales service.
FCO, FC 1 or FC2	Abnormal communication error.	• Contact the After sales service.
Unb	Unbalanced load error.	• Check and balance laundry load in the drum. • Reduce the load.
Washing machine fails to operate.	• Programme is not yet started. • Door is not properly closed. • Machine has not been switched on. • Power failure. • Child lock is activated.	• Check programme and start it. • Close the door properly. • Switch the machine on. • Check power supply. • Deactivate child lock.
Washing machine will not be filled with water.	• No water. • Inlet hose is kinked. • Inlet hose filter is blocked. • Water pressure is less than 0.03 MPa.	• Check water tap. • Check inlet hose. • Unblock inlet hose filter. • Check water pressure.
Machine is draining while being filled.	• Door is not properly closed. • Water supply failure.	• Close the door properly. • Ensure the water supply.
Drainage failure.	• Height of drain hose is below 80 cm. • Drain hose end could reach into water. • Drain hose is blocked. • Pump filter is blocked. • Drain hose end is higher than 100 cm above floor level.	• Make sure that drain hose is properly installed. • Make sure the drain hose is not in water. • Unblock drain hose. • Clean pump filter. • Make sure that drain hose is properly installed.
Strong vibration while spinning.	• Not all transportation bolts have been removed. • Appliance has no solid position. • Machine load is not correct.	• Remove all transportation bolts. • Ensure solid ground and a ev-elled position. • Check load weight and balance.
Operation stops before completing wash cycle.	• Water or electric failure.	• Check power and water supply.
Operation stops for a period of time.	• Appliance displays error code. • Problem due to load pattern. • Programme performs soaking cycle.	• Consider display codes. • Reduce or adjust load. • Cancel programme and restart.
Excessive foam floats drum and/or detergent drawer.	• Detergent is not a appropriate. • Excessive use of detergent.	• Check detergent recommen-dations. • Reduce amount of detergent.
Automatic adjustment of washing time.	Washing programme duration will be adjusted.	• This is normal and doesn't af-fect functionality.
Spinning fails.	• Unbalance of laundry.	• Check machine load and laun-dry and run a spinning pro-gramme again.
Unsatisfactory washing result.	• Degree of pollution does not agree with selected programme • Detergent quantitiy was not suf-ficient. • Maximum load has been excee-ded. • Laundry was unevenly distribu-ted in the drum.	• Select an other programme. • Choose the detergent acc. to the degree of pollution and according to manufac-ture specifications. • Reduce loading. • Loose the laundry.
Washing powder residues are on the laundry.	• Insoluble particles of detergent can remain as white spots on the laun-dry.	• Perform extra rinse. • Try to brush the points from the dry laundry.
Laundry has grey patches.	• Caused by fats such as oils, creams or ointments.	• Choose an other detergent. • Preheat the laundry with a spe-cial cleaner.