Manual for EWT 1066 TDW

Manual for EWT 1066 TDW

Brand: ELECTROLUX

Category: Washing Machine

Document Type: Manual

Language: EN

Uploaded: Nov. 21, 2025, 8:16 p.m.

Daily Use

  1. Open the water tap and connect the mains plug.
  2. Open the appliance lid and the drum.
  3. Load laundry one item at a time, ensuring not to overload. Close the drum and lid securely.
  4. Measure and add detergent and fabric conditioner.
  5. Activate the appliance and set the desired programme using the programme knob.
  6. Adjust temperature, spin speed, or add options as needed.
  7. Press the Start/Pause button to begin the cycle.

Interrupting and Cancelling

  • Press the Start/Pause button to interrupt. Re-press to continue or change options.
  • Press and hold the On/Off button to cancel the programme and deactivate the appliance.

End of Programme

  • The appliance stops automatically.
  • Remove laundry, close the water tap, and leave the lid ajar.

Troubleshooting and error codes

Problem Possible solution
The programme does not start. Make sure that the mains plug is connected to the mains socket. Make sure that the appliance lid is closed. Make sure that there is not a damaged fuse in the fuse box. Make sure that the Start/Pause has been pressed. If the delay start is set, cancel the setting or wait for the end of countdown. Deactivate the Child Lock function if it is on.
The appliance does not fill with water. Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to “Care and cleaning”. Make sure that the inlet hose has no kinks or bends.
The appliance does not drain the water. Make sure that the connection of the water inlet hose is correct. Make sure that the sink spigot is not clogged. Make sure that the drain hose has no kinks or bends. Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'. Make sure that the connection of the drain hose is correct. Set the drain programme if you set a programme without drain phase. Set the drain programme if you set an option which ends with water in the tub.
The spin phase does not operate or the washing cycle lasts longer than usually. Set the spin programme. Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to 'Care and cleaning'.
There is water on the floor. Adjust manually the items in the tub and start the spin phase again. This problem may be caused by balance problems. Make sure that the couplings of the water hoses are tight and there is not water leakages. Make sure that the drain hose have no damages. Make sure you use the correct detergent and the correct quantity of it.
You cannot open the appliance lid. Make sure that the washing programme is finished. Set the drain or the spin programme if there is water in the drum.
The appliance makes an unusual noise. Make sure the levelling of the appliance is incorrect. Refer to 'Installation'. Make sure that the packaging and/or the transit bolts are removed. Refer to 'Installation'. Add more laundry in the drum. The load may be too small.
The appliance fills with water and drain immediately. Make sure that the drain hose is in the correct position. The hose may be too low.
The washing results are not satisfactory. Increase the detergent quantity or use a different detergent. Use special products to remove the stubborn stains before you wash the laundry. Make sure that you set the correct temperature. Decrease the laundry load.
You cannot set an option. Make sure that you press only the wanted pushbutton(s).
After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the Service. If the display shows other alarm codes. Deactivate and activate the appliance. If the problem continues, contact the Service.
Privacy Policy