Brand: AEG
Category: Cooktop
Document Type: Manual
Language: EN
Manual for HKM95600IB
Uploaded: April 20, 2026, 7:59 p.m.
Warranty Information
Consult the guarantee booklet for information about the Authorised Service Centre and warranty conditions.
The AEG HKM95600IB is an induction cooktop designed for efficient cooking. Key operations include activating and deactivating the hob, using the heat settings via a control bar, and utilizing various functions like Bridge, Power, Chef, Automatic Heat Up, timers (Count Down and Count Up), and STOP+GO. Safety features include Child Safety Device and OffSound Control. The hob also features OptiHeat Control for residual heat indication and Automatic Switch Off for safety. Ensure correct cookware is used for optimal performance and energy saving by using lids and the residual heat.
Troubleshooting and error codes
| Problem | Possible cause | Remedy |
|---|---|---|
| You cannot activate or operate the hob. | The hob is not connected to an electrical supply or it is connected incorrectly. | Check if the hob is correctly connected to the electrical supply. Refer to the connection diagram. |
| The fuse is released. | Make sure that the fuse is the cause of the malfunction. If the fuse releases again and again, contact a qualified electrician. | |
| An acoustic signal sounds and the hob deactivates. | You touched 2 or more sensor fields at the same time. | Activate the hob again and set the heat setting in less than 10 seconds. Touch only one sensor field. |
| STOP+GO function operates. | Refer to "Daily use" chapter. | |
| There is water or fat stains on the control panel. | Clean the control panel. | |
| An acoustic signal sounds when the hob is deactivated. | You put something on one or more sensor fields. | Remove the object from the sensor fields. |
| The hob deactivates. | You put something on the sensor field. | Remove the object from the sensor field. |
| Residual heat indicator does not come on. | The zone is not hot because it operated only for a short time. | If the zone operated sufficiently long to be hot, speak to an Authorised Service Centre. |
| Automatic Heat Up function does not operate. | The zone is hot. | Let the zone become sufficiently cool. |
| The heat setting changes between two levels. | Power management function is activated. | Refer to "Daily use" chapter. |
| The sensor fields become hot. | The cookware is too large or you put it too near to the controls. | Put large cookware on the rear zones if possible. |
| There is no signal when you touch the panel sensor fields. | The signals are deactivated. | Activate the signals. Refer to "Daily use" chapter. |
| comes on. | Automatic Switch Off operates. | Deactivate the hob and activate it again. |
| L comes on. | The Child Safety Device or the Lock function operates. | Refer to "Daily use" chapter. |
| F comes on. | There is no cookware on the zone. | Put cookware on the zone. |
| The cookware is incorrect. | Use the correct cookware. Refer to "Hints and tips" chapter. | |
| The diameter of the bottom of the cookware is too small for the zone. | Use cookware with correct dimensions. Refer to "Technical information" chapter. | |
| The cookware does not cover the cross / square. | Cover the cross / square fully. | |
| E and a number come on. | There is an error in the hob. | Disconnect the hob from the electrical supply for some time. Disconnect the fuse from the electrical system of the house. Connect it again. If E comes on again, speak to an Authorised Service Centre. |
| E3 comes on. | The electrical connection is incorrect. The supply voltage is out of range. | Speak to a qualified electrician to check the installation. |
| E4 comes on. | There is an error in the hob because a cookware boils dry. Automatic Switch Off and the overheating protection for the zones operate. | Deactivate the hob. Remove the hot cookware. After approximately 30 seconds, activate the zone again. If the cookware was the problem, the error message goes out. Residual heat indicator can stay on. Let the cookware become sufficiently cool. Check if your cookware is compatible with the hob. Refer to "Hints and tips" chapter. |
| E7 comes on. | The cooling fan is blocked. | Check if objects block the cooling fan. If E7 comes on again, speak to an Authorised Service Centre. |
| E8 comes on. | The electrical connection is incorrect. The hob is connected only to one phase. | Speak to a qualified electrician to check the installation. Refer to the connection diagram. |